Com5 putty download how to#
Com5 putty download serial#
Com5 putty download driver#
Com5 putty download software#
Com5 putty download download#

Com5 putty download driver#

So I would say that it sounds like a PC-side issue it you canвЂ™t open the COM port associated to the deviceвЂ¦ Maybe a driver one?ДЄ simple question: before trying to download, did you switched the module USB mode in вЂњCOMвЂќ mode? This will help to know which driver is enabled on your PC. I am not sure if it should show COM5 instead? However Windows Devices Manager identifies COM5 while Developer Studio 2.1.1 shows COM1. Yes the com port associated to the USB device is disappearing/reappearing, when keeping WindowsвЂ™ Devices Manager opened. That is not reliable at load!Д¬an you make a try to keep the WindowsвЂ™ Devices manager opened, and unplug/replug the module USB cable, to confirm that your COM port associated to the USB device is disappearing/reappearing? Why would the module be blocked in bootloader mode? The boot loader should always be there and working, or reset on power cycle. The LED going from ON to OFF after reset is a typical symptom of a module вЂњblockedвЂќ in bootloader mode. I do not know if that has any effect in the issue or in resolving the issue.

Com5 putty download serial#

So far every solution requires communication and I do not have any communication, which by the way I had before through USB and serial port.Д«y the way I have and FXTE02 extension card installed for Ethernet communication. So that why I am looking for a way to do hardware reset. So far as long as the LED is off I have not been able to communicate with the FXT009 form any port what so ever. When I turn it on, the LED come on the goes off and stays off. The thing that is strange is my LED is off even though I know the FXT009 has power. So I cannot send anything right now from any port: serial or usb. I checked device manager to make sure that COM5 was the port where my USB cable was assigned to. I then tried Putty on windows 7: I get 'Unable to communicate to COM5. So the only thing that is not working is the FXT009. Make sure it is properly connected and turned on. I used device manager from windows 7, trying to query the FXT009 here is the error I get: As soon as you can see chars echoed back, it will mean that youвЂ™re in the bootloader AT interface mode. Bootloader may need this to synchronize on the port. To recover your modem, please try to open the connection on the USB port with another communication software, and to send several вЂњaвЂќ characters. I am confident we can get to the bottom of the issue and get this resolved. Thank you everybody for your help so far. So I am wondering of an easy way to hardware reset the FXT009 to factory default (like a hard reset switch)? I have no way to check since none of the ports are working. So right now I am not sure the bootloader is running. And this is supposed to be the default for the serial port. I am using Putty on windows Vista: baud 115200, data bits 8, stop bits 1, parity none, Flow control RTS/CTS. Tried communication via serial port, but no communication there either. When powering up FXT009, LED comes on for 1 sec or less and then goes off and stays off.

Com5 putty download download#

Download hanged up, then cancelled and lost communication via USB and LED on FXT009 turned off by itself.ДЄttempted cycle power on FXT009, cycle power on PC, but nothing. Download hanged up, then cancelled and still had communication via USB.LED on FXT009 was still blinking on and off.

Com5 putty download software#

IвЂ™ll go back to you ASAP, when I get more details from the embedded software team about this particular use case.ДЇW versions out of the box prior to download attempt: FW 7.05250600-1 Please can you just elaborate on what are the concerned FW versions (I mean the original one which was running on the module, and the new one you were attempting to download)? Is the serial communication a fallback port that I should try since the USB port since not to be working? Is the FXT09 dead since the front RED LED does not flash or stay on?Дid I flush the firmware and therefore there is nothing running on the FXT09?

Com5 putty download how to#

How to I get the FXT09 back to the factory default which I know was working fine? The TMC console does not respond to any AT command. Open port COM1 => ERROR: Time out: 10000ms

Open and load physical port COM1 => ERROR: Time out: 10000ms Open and load port COM1 => ERROR: Time out: 10000ms When attempting to open the USB port to communicate using the Target Manager of developer studio here is the errors: Before it was flashing on and off when everything was working prior to the download attempt. Now the FXT09 front LED turn on RED on power-up and stays off. I do not know if this is what created the problem. I cancelled the download while it was still downloading. The FXT09 is not communicating through USB anymore after an attempt to download Firmware, using Development studio 2.1.1.